Please use the Size Your Water Softener Calculator. It will appropriately size the water softener system for your needs. It walks you through two simple steps that will guide you through choosing the proper size and explain the pros and cons of each control valve. It's simple and quick.
All Of These Options Are Included At No Additional Charge.
Q. What is a Bypass Valve for?
A. The Bypass valve is needed to put the water softener in bypass and still have water to the house. It's like having insurance it is there if you need it, but is seldom used. Note: if you already have a bypass valve installed in your plumbing system, use the Bypass Valve drop down menu to remove it from your order. This will lower your price by $16.00.
Q. What is a Safety Float?
A. The safety float is an emergency float. Its function is to make sure that the salt tank cannot overflow salt water all over your floor if the injectors on the water softener valve get plugged up. Without the safety float you could have a mess on your hands not to mention possible damage to the floor.
Q. What is a Brine Well for?
A. Brine well isolates the air check valve on the safety float from the rock salt or potassium chloride a substitute for rock salt that is environmentally friendly and healthy for humans from clogging up the air check valve and the water softener valve.
Q. What is a Grid Plate AKA Salt Platform?
A. Grid plate is at the bottom of the salt tank its purpose is to help the salt or potassium chloride from bridging up hardening over the top of the water. When this happens the water can’t dissolve the salt so when the water softener regenerates the resin beads will not get charged and your water will be hard.
Q. Why is the 8% Crosslink Resin better?
A. 8% crosslink is more resistant against chlorine than the 6% that most other companies offer. Therefore, the resin is intended to last longer.
Q. Why is an appropriate size mineral a.k.a Resin Tank important?
A. It is important to have a minimum of 12” to 15” of space between the top of the resin bed and the bottom of the control valve so the resin can get lifted and cleaned properly during backwash. If there is not proper space the resin will not perform properly and will go bad quickly. All of our tanks our sized properly and allow the proper 12” to 15” space.
Q. What size Brine Tank should I choose?
A. If you have the floor space choose the round 18x33 brine tank. It is built better than the rectangular and square tanks and holds more salt. We do not charge for the 18x33 brine tanks. Choose the size that is best for your application on our drop down menu. Please note: 64,000 grain capacity water softeners and up will not work properly with smaller brine tanks.
SHIPPING IS FREE TO LOWER 48 STATES ON ALL WATER SOFTENERS! For fast delivery we ship from the closest State to you, Ohio, Florida or Arizona.
Note: We are not affiliated
with any other companies.
Fleck 9100TS Twin Sensor On Demand Water Softeners
• Most Efficient Softener on
the market
• Logix Controls
• Patented Sensor
technology
• Upflow Regeneration
The best next thing.
The NEW Pentair Water 9100TS Water Conditioning System ensures softened water 24/7. Patented sensor technology maximizes conditioning capacity to 100% which can save up to 35% in regenerant and water!
Twin-tank design delivers a never-ending supply of conditioned water.
Dual sensors accurately measure fluctuations in water hardness through resin conductivity
Replaces systems with traditional metered and time clock controls
Pentair’s patented cell technology
measures the conductivity through
resin bed to calculate true capacity
and accommodate for fluctuations
in water hardness– Los Angeles hardness varies from
5 to 20 grains/gallon, with an
average of 16. Compared to
softener set for maximum
removal, the 9100TS will realize
an efficiency improvement of 20%
ProSoft Water Systems Elite digital metered water softener / conditioner meters water usage and regenerates only when it needs to. Using high capacity resin, ProSoft metered on demand smart valve, media guard filter, Stainless humidity jacket, Vortech technology and a Limited Lifetime Warrantytruly make this system the best the market has to offer.
ProSoft Water Systems gives you the following benefits over the traditional systems.
1). Memorizes daily usage so you will not run out of soft water
2). The optional double backwash program removes iron from the resin bed. Resin expands after is has been dosed with a dilute brine solution and breaks loose attached iron which is backwashed out of the unit in the second backwash cycle. This minimizes the use of iron cleaning salts or additives
3). Less moving parts than most other controls, saving you money on eventual replacement parts and breakdowns.
4). Memory back up in case of power loss, this system will hold its memory and the time of day so no resetting needed.
5). Media guard filter of your choice to remove Chlorine, heavy metals and put a protective coating on pipes and hot water heaters to protect them from corrosion.
6). Limited lifetime warranty compared to traditional softeners which only have a 5 -10 year warranty and no warranty on resin.
7). Vortech tank technology supplies higher flow rates and saves Salt - Saves you money & time.
8).Stainless tank jacket that protects tank and helps the tank from sweating.
Get your ProSoft Water System today and start enjoying Soft and Conditioned water throughout your home.
WOW, Now available to the public! Water Softeners using the famous Fleck 6700 XTR Metered control valve for Professional Dealers is now available to the public at wholesale cost.
This valve has many great features.
For more than 50 years, Fleck Corporation has offered water treatment professionals the widest selection of products in the industry.
In 2001, after years of development and extensive field testing, Fleck introduced the 6700 XTR control valve for Dealers only.
The ProSoft Water Systems softeners are the best engineered and most efficient single column systems available in the industry today and the one that we sell and install for our own retail customers.
Control valve manufacturers have always offered a better grade control valve to be marketed through water conditioning professionals only. Since we qualify as a water conditioning professional, we have decided to offer this system to the do-it-yourself customer through the Internet.
This control, manufactured by Fleck/Pentair Controls, will keep the time current in the advent of a power outage.
The optional double backwash program removes iron from the resin bed. Resin expands after is has been dosed with a dilute brine solution and breaks loose attached iron which is backwashed out of the unit in the second backwash cycle. This minimizes the use of iron cleaning salts or additives.
Less moving parts than most other controls, saving you money on eventual replacement parts and breakdowns.
Mechanical Meter that will still
count your water usage even in the event of a
power failure. this meter consist of a dome that
is on the back of the 2510 valve. Inside this
dome is an impeller. Coming off the top of the
dome is a cable that runs to the meter assembly
that is attached to the 2510 controller. When
you use water, the impeller turns and that turns
the cable, the cable is what turns the meter assembly
which is where you have set the amount of gallons
you are going to use before a regeneration.
The main difference between the 5600
model and the 2510 is:
1) Metal Back plate that holds all the components
instead of plastic brackets.
2) The valve is 1" internally giving you
higher flow rates with less pressure drop than
the 5600 fleck valves.
3) Has Two motors instead of one. Uses a Timer
motor to keep the time of day and has a heavy
duty Myrcle Drive motor that is attached directly
to the piston which eliminates a lot of gear movement.
This System is especially great for homes that
are 2400 square feet or larger
do to its ability to supply you with higher flow
rates than the 5600 valves. But can also be used
on smaller homes as well.
Digital Electronic Meter that counts your water usage thru a electric pulse. on the discharge side of the system is a turbine assembly, attached to the assembly is a probe that goes to the SXT control valve. As water runs through it the turbine assembly sends a signal to the SXT controller and reads your water usage.
Fleck's new SXT controller is the next generation upgrade to its current SE Controller platform. It features the same basic functionality of the SE, but with a few added extras. The SXT Controller offers a larger, backlit display, new diagnostic view, improved programming code options, and a super capacity power backup of over 48 hours. Integrated with the reliable, durable Fleck 2510, this makes for a long lasting, dependable valve.
The main advantage that the 2510 SXT has
over the 2510 Econominder is:
1) You can go into the master programming mode
and customize the system by having it backwash
and rapid rinse for longer or shorter periods
of time, adjust salt pounds all with a touch of
a button.
2 ) Solid state microprocessor with LED display.
Time of day, Remaining capacity, Regeneration
cycle in process.
3 ) Compact turbine meter assembly
4 ) Higher metering capability.
5 ) NOVRAM valve status and memory backup.
6 ) Reads your water usage electronically equals
less moving parts than it's ancestor the Econominder.
7) Easy to Program
This System is especially great for homes that
are 2400 square feet or larger
do to its ability to supply you with higher flow
rates than the 5600 valves. But can also be used
on smaller homes as well.
Mechanical Meter that will still
count your water usage even in the event of a
power failure. this meter consist of a dome that
is on the back of the 5600 valve. Inside this
dome is an impeller. Coming off the top of the
dome is a cable that runs to the meter assembly
that is attached to the 5600 controller. When
you use water, the impeller turns and that turns
the cable, the cable is what turns the meter assembly
which is where you have set the amount of gallons
you are going to use before a regeneration.: The
5600 Valve has been in production since 1979!
Features:
1). Simple mechanical design is easy to understand.
2). Two valve body designs: one for downflow
regeneration and one for upflow (covers every
valve in the 5600 family - quick access to all
internal components).
3). Injector/drain modules containing the brine
valve, flow controls and injector are removable
from the valve's exterior.
4). Ruggedly built timer is designed with heavy-duty
3/8" wide plastic gears.
5). 5600 controls are user friendly and easy
to program.
Digital Electronic Meter that
counts your water usage thru a electric pulse.
on the discharge side of the system is a turbine
assembly, attached to the assembly is a probe
that goes to the SXT control valve. As water runs
through it the turbine assembly sends a signal
to the SXT controller and reads your water usage.
Fleck's new SXT controller is the next generation
upgrade to its current SE Controller platform.
It features the same basic functionality of the
SE, but with a few added extras. The SXT Controller
offers a larger, backlit display, new diagnostic
view, improved programming code options, and a
super capacity power backup of over 48 hours.
Integrated with the reliable, durable Fleck 5600,
this makes for a long lasting, dependable valve.
Difference between the 5600 Econominder
and the 5600SXT:
1). Large LCD display with 48 hours of internal
power backup capacitor.
2). LCD display alternates between time of day,
volume remaining or days to regeneration.
3). Compact turbine meter.
4). Downflow regeneration cycles.
5). Choose from 4 modes of operation: immediate
meter regeneration, delayed meter regeneration,
delayed time clock regeneration or day of week
regeneration with a touch of a button.
6). Double backwash capability to clean resin
bed of iron if present.
7). Higher meter capability up to 9,999 gallons
compared to the 5600econdominder of 2100 gallons.
8). Reads your water usage electronically equals
less moving parts than it's ancestor the Econominder.
Digital Electronic Meter that counts your water usage thru a electric pulse. on the discharge side of the system is a turbine assembly, attached to the assembly is a probe that goes to the SXT control valve. As water runs through it the turbine assembly sends a signal to the SXT controller and reads your water usage.
Fleck's new SXT controller is the next generation upgrade to its current SE Controller platform. It features the same basic functionality of the SE, but with a few added extras. The SXT Controller offers a larger, backlit display, new diagnostic view, improved programming code options, and a super capacity power backup of over 48 hours. Integrated with the reliable, durable Fleck 7000, this makes for a long lasting, dependable valve.
The main advantage that the 7000 SXT has
over the 5600 & 2510 models is:
Mechanical
Meter that will still count your water
usage even in the event of a power failure. this
meter consist of a dome that is on the back of
the 9000 valve. Inside this dome is an impeller.
Coming off the top of the dome is a cable that
runs to the meter assembly that is attached to
the 9000 controller. When you use water, the impeller
turns and that turns the cable, the cable is what
turns the meter assembly which is where you have
set the amount of gallons you are going to use
before a regeneration.
Important Features:
1) Regenerates with treated water.
2) You don't have to back off your meter gallons
by one day for reserves do to when the meter expires
on this system it regenerates right then and switches
to the other tank to supply you with unlimited
treated water 24 hours a day.
3) No Clock to reset incase of power loss.
4) All Brass Valve Body instead of Noryl
5) 1" Copper Manifold between Tank 1 and
2 is already put together for you.
6) The valve is 1" internally giving you
higher flow rates with less pressure drop than
the 5600 fleck valves.
7) Has Two motors instead of one. Uses a Timer
motor to activate the regeneration process and
has a heavy duty Myrcle Drive motor that is attached
directly to the piston which eliminates a lot
of gear movement.
Digital
Meter Easy to program, novram memory
chip keeps your programming during a power failure.
¾" valve and meter with Plastic valve and manifold.
Important Features:
1) Regenerates with treated water.
2) You don't have to back off your meter gallons
by one day for reserves do to when the meter expires
on this system it regenerates right then and switches
to the other tank to supply you with unlimited
treated water 24 hours a day.
3) No Clock to reset incase of power loss.
4) Uses 15 % less salt and water.
5) Has Two motors instead of one. Uses a Timer
motor to activate the regeneration process and
has a heavy duty Myrcle Drive motor that is attached
directly to the piston which eliminates a lot
of gear movement.
Vortech – the world’s newest, innovative
and most efficient bottom distribution system.
Cleaning is greatly improved, freeboard is reduced,
and it works with all softening and filtration
medias. The Vortech’s high flow design maximizes
today’s high efficiency valves . . . now
your smart valve has a smart tank!
Features & Benefits
• Up to 30% less backwash flow rate is required.
. . conserving water for the consumer.
• High flow design maximizes today’s
high efficiency valve technology.
• Permanent attachment of dip tube to distributor,
so when servicing a valve, distributor stays in
place, no more re-bedding.
• Vortech distributor plate is designed
for over 6,500 lbs load capacity.
• Improved system pressure drop characteristics.
• Self-cleaning nozzle design eliminates
potential clogging and build-up.
• Available for 9”, 10”, 12”
and 13” tanks; adapters for 1” and
1 ¼” valves.
• Increase in softening capacity, due to
improved flow through media.
• No channeling of media, providing a cleaner
more efficient system.
• Environmentally friendly, reduction in
required backwash times due to improved bed lift
and mixing . . . at lower flow rates.
• Most efficient softening regeneration,
reducing salt consumption.
Fleck 2510SXT digital metered water
softener meters water usage and regenerates only
when it needs to. Using a cross link 10 SST-60
resin cuts your salt and water usage in half saving
you money and is healthier for the environment.
Specifications: 2510SXT digital metered valve, 10 x 54
mineral tank, 18x33 brine tank, 1/5 cuft of sst-60
resin, 1" or 3/4" stainless steel bypass valve,
safety float, grid plate, brine well, funnel to
add resin for first time, decorative chrome jacket.
48,000 grain capacity
Time
clock systems are more economical in
price than the metered on demand systems and can
be set to regenerate on specific days instead
of by gallons. You have the ability to set it
to regenerate from every day to every 12 day's.
The 5600 Valve has been in production since 1979!
The problem is that they do not know when the
resin is at its full capacity like a metered on
demand system does, which sometimes causes you
to run out of treated water before it regenerates
or regenerate when it does not need to thus wasting
water and salt.
Benefit:
If you are on your own private well with iron
levels above 2 ppm or mg/L then the time clock
style may be a better choice for you being it
will regenerate the resin more often keeping the
resin clean and from fouling out by the iron.
Besides that and the price there is no other benefits.
Time
clock valve regenerates on days set instead of
gallons used, you have the ability to
set it to regenerate every day to every 12 day's.
The main difference between the 5600
model and the 2510 is:
1) Metal back plate that holds all the components
instead of plastic brackets.
2) The valve is 1" internally giving you higher
flow rates with less pressure drop than the 5600
fleck valves.
3) Has two motors instead of one. Uses a timer
motor to keep the time of day and has a heavy
duty Myrcle drive motor that is attached directly
to the piston, which eliminates a lot of gear
movement.
This System is particularly great for
homes that are 2400 square feet or larger
do to its ability to supply you with higher flow
rates than the 5600 valves. But can also be used
on smaller homes as well.
State of the art microprocessor 460i digital
meter that has jumpers that you set on the hardness
of your water and the capacity of your system
i.e. 32,000 grain for example.
Important Features:
1) Novram valve status and memory backup.
2) Reads your water usage electronically equals
less moving parts.
We Sell The Best Quality Equipment Available At The Lowest
Prices Available To The Public!.
All equipment is NEW and manufactured in the
USA or Canada.
All Orders are Shipped directly to you from our Distributor located in Florida,
Ohio or Arizona! FREE SHIPPING FOR ALL ORDERS OVER $30 AT QUALITY
WATER TREATMENT!!!
All orders are shipped same business day if placed before 1:00 P.M. EST.
Check out our Reviews,
our competition can't compete with us! "WE PROMISE"
Water Softeners, Home Water Softener, Water
Softener Comparison, Water Softener Systems, Water Softener
Reviews,
Saltless Water Softener,
Fleck Water Softeners, Autotrol Water Softeners, Ge
Water Softeners , General Electric Water Softeners
